 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| a u s t ri a m i c r o s y s t e m s AS3682 480mA Camera Lighting Management Unit P ro du c t B ri e f 1 General Description The AS3682 is a low-noise, high-current charge pump designed for camera flash LEDs and LCD backlighting applications. The device is capable of driving up to 480mA of load current. The AS3682 integrates two independent LED blocks for driving a single flash LED (CURR11 to CURR13) with up to 480mA, and general purpose LEDs (CURR2 to CURR4) with up to 160mA/LED. The general purpose LEDs are controlled individually and can be used for backlighting, but also in support of an RGB fun-light or a movie indicator lamp. The AS3682 utilizes austriamicrosystems's patent-pending Intelligent Adaptive Mode Setting (IAMS) to switch between 1:1, 1:1.5, and 1: 2 modes. In combination with very-low-drop-out current sinks, the device achieves high efficiency over the full single-cell Li+ battery voltage range. The charge pump operates at a fixed frequency of 1MHz allowing for tiny external components and its design ensures low EMI and low input-ripple. The ultra-flexible brightness control scheme allows for simple adaptation of the device to different system architectures. In Normal and Softflash Modes the device is controlled by an I2C interface. In these modes the LED brightness, flash duration, GPIOs and various charge pump states are controlled by internal register settings. The GPIO pins can act as programmable input or output pins and can also be set to trigger preview and flash light directly by a camera module. In Hardflash Mode, the LED brightness is controlled by the Enable pins. Those programming pins can be used as simple enable pins, as PWM input, again offering ample flexibility for setting the LED brightness. 2 Key Features ! High-Efficiency High-Power Charge Pump - 1:1, 1:1.5, and 1:2 Intelligent Adaptive Mode Setting (IAMS) - Efficiency up to 95% - Soft Start to Reduce Inrush Current - Low-Noise Constant-Frequency Operation Current Sinks - 400mA Continuous Flash Current (@VIN = 3.2 to 5V, VOUT = 5V) - 480mA Maximum Pulsed Flash Current - Programmable: 0 to 160mA, 0.625mA Resolution Flexible Brightness Control - Three 0 to 160mA LEDs - Individually Addressable via I2C Interface Three Operating Modes - Normal Mode (I2C Interface) - Softflash Mode (I2C Interface) - Dedicated Control Pins for Hardflash Modes ! ! ! ! Two General Purpose Inputs/Outputs - Digital Input, Output, and Tristate - Programmable Pull-Up and Pull-Down - Strobe Pin can be used for Camera Flash Control LED Disconnect in Shutdown Open LED Detection Low Stand-By Current (6A), Interface Fully Operating Low Shut-Down Current (0.2A) Wide Battery Supply Range: 3.0 to 5.5V Thermal Protection 24-Pin, Small Form-Factor QFN Package - 4 x 4 x 0.85mm, 0.5mm Pitch - Enhanced Thermal Characteristics ! ! ! ! ! ! ! 3 Applications Lighting management for cameras, mobile telephones, PDAs, and other 1-cell Li+ or 3-cell NiMH powered devices. (c) 1997-2005, austriamicrosystems AG, 8141 Unterpremstaetten, Austria-Europe. All Rights Reserved. www.austriamicrosystems.com Revision 2.1 1-4 AS368 2 Product Brief austriam i c r o systems 4 Block Diagram Figure 1. AS3682 Block Diagram V2_5 22 AS3682 Digital Supply 2 6 5 VBAT1 VBAT2 C2_P C2_N C1_P C1_N CP_OUT RBIAS 23 Bandgap and Current Reference Charge Pump 1:1, 1:1.5, 1:2 7 3 24 4 ADR 1 VDD_GPIO 12 CLK/P2 DATA/P1 8 9 Digital Part Serial Interface Mode Selector Current Source STROBE/F2 11 13 14 CURR11 CURR12 CURR13 GPIO0/P0 10 15 SFL/F1 16 Current Source T1/F0 17 19 CURR2 20 HFL 18 21 CURR3 CURR4 GND Exposed Pad 5 Application Diagrams Figure 2. Normal and Softflash Mode Application Diagram V2_5 1F C3 RBIAS 23 5 240k R1 7 V2.5 = 41h GND = 40h ADR 1 3 VDD_GPIO 12 24 C1_P C1_N 1F C5 C2_P C2_N 1F C4 22 2 6 VBAT1 VBAT2 2.2F C1 Battery Feature Interface Current Sinks Addressable Strobe Trigger Strobe Preview Camera 2.2F Flash LED C6 Normal Mode I 2C 3 Softflash Mode I2C 3 0 to 480mA Block Total Current 0 to 450mA Flash LEDs Block STROBE/F2 STROBE/F2 or software or software GPIO0/P0 or software 3 GPIO0/P0 or software 3 1 - 10k R4 DATA/P1 9 AS3682 4 CP_OUT Flash & Preview CLK/P2 8 13 CURR11 General Purpose LEDs (CURR2, CURR3, CURR4) Current Sinks Current per Sink Addressable 0 to 37.5mA 0 to 160mA Individual Individual STROBE/F2 11 14 CURR12 15 19 CURR13 CURR2 GPIO0/P0 SFL Mode: SFL/F1 = VDD_GPIO Normal Mode: SFL/F1 = GND 10 SFL/F1 16 Battery or CP_OUT T1/F0 HFL 17 18 20 CURR3 21 CURR4 GND Exposed Pad (c) 1997-2005, austriamicrosystems AG, 8141 Unterpremstaetten, Austria-Europe. All Rights Reserved. www.austriamicrosystems.com Revision 2.1 2-4 AS368 2 Product Brief austriam i c r o systems Figure 3. Hardflash Mode 1 Application Diagram V2_5 1F C3 22 2 6 5 7 VDD_GPIO Selectable DATA/P1 MSB Preview CLK/P2 8 9 24 C1_N 12 3 VBAT1 VBAT2 2.2F C2_P C2_N C1_P 1F C5 1F C4 C1 Battery Feature Interface Current Sinks Total Current Flash LEDs Addressable Hardflash Mode 1 Dedicated Control Pins for Strobe (3x) & Preview (3x) 6 Strobe: 0 to 450mA Preview: 0 to 400mA Block By Preview Control Pins N/A N/A N/A RBIAS ADR 23 1 240k R1 Strobe Trigger By Strobe Control Pins Strobe Preview Camera 2.2F Flash LED C6 AS3682 4 CP_OUT Flash & Preview Preview Control (Active Low) GPIO0/P0 LSB Preview STROBE/F2 MSB Flash SFL/F1 10 13 14 15 CURR11 CURR12 CURR13 CURR2 General Purpose LEDs (CURR2, CURR3, CURR4) Current Sinks Current per Sink Addressable 11 16 19 Strobe Control (Active Low) T1/F0 LSB Flash Battery HFL 17 20 CURR3 GND 18 21 CURR4 Exposed Pad Figure 4. Hardflash Mode 2 Application Diagram Feature Battery V2_5 1F C3 22 2 6 5 7 VDD_GPIO Selectable DATA/P1 MSB Preview CLK/P2 8 9 24 C1_N 12 3 VBAT1 VBAT2 2.2F C2_P C2_N C1_P 1F C5 1F C4 C1 Hardflash Mode 2 Dedicated Control Pins for Flash (3x) & General Purpose (3x) Interface Current Sinks Total Current Flash LEDs Addressable Strobe Trigger Strobe Preview Current Sinks General Purpose LEDs (CURR2, Current per Sink CURR3, CURR4) Addressable Camera 2.2F Flash LED C6 RBIAS ADR 23 1 3 Flash: 0 to 450mA Block By Flash Control Pin 3 0 to 20/37.5mA Block 240k R1 AS3682 4 CP_OUT Flash & Preview Backlight Control (Active Low) GPIO0/P0 LSB Preview STROBE/F2 MSB Flash SFL/F1 10 13 14 15 CURR11 CURR12 CURR13 CURR2 11 16 19 Flash Control (Active Low) T1/F0 LSB Flash Battery HFL 17 20 CURR3 GND 21 18 CURR4 Exposed Pad (c) 1997-2005, austriamicrosystems AG, 8141 Unterpremstaetten, Austria-Europe. All Rights Reserved. www.austriamicrosystems.com Revision 2.1 3-4 AS368 2 Product Brief austriam i c r o systems Copyrights Copyright (c) 1997-2005, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG A-8141 Schloss Premstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 e-mail: info@austriamicrosystems.com For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com austriamicrosystems - a leap ahead 4-4 (c) 1997-2005, austriamicrosystems AG, 8141 Unterpremstaetten, Austria-Europe. All Rights Reserved. www.austriamicrosystems.com Revision 2.1 |
Price & Availability of AS3682NBSP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |